Error Code/Symptom FRU/Action 062 (Three consecutive boot failures using the default configuration.)
1. Run Configuration/Setup
2. Battery
3. System board
4. Microprocessor
101, 102, 106 (System and microprocessor error) System board 111 (Channel check error)
1. Failing adapter
2. DIMM
3. System board
114 (Adapter read only memory error)
1. Failing adapter
2. Run diagnostics
129 (Internal cache error) Microprocessor 135 (Fan failure)
1. Run Configuration/Setup
2. Fan
3. System board
151 (Real time clock error)
1. Run diagnostics
2. Battery
3. System board
161 (Real time clock battery error)
1. Run Configuration/Setup
2. Battery
3. System board
162 (Device configuration error)
NOTE: Be sure to load the default settings and any additional desired settings; then, save the configuration.
1. Run Configuration/Setup
2. Battery
3. Failing device
4. System board
163 (Real time clock error)
1. Run Configuration/Setup
2. Battery
3. System Bbard
164 (Memory configuration changed, see 'IBM Setup Utility main menu choices'
1. Run Configuration/Setup
2. DIMM
3. System board
166 (Boot block checksum error) System board 167 (No process BIOS update found) Flash to latest BIOS 175 (Hardware error) System board 176, 177, 178 (Security hardware error)
1. Run Configuration/Setup
2. System board
179 (Boot integrity services segment error) Flash BIOS 184 (Power on password corrupted)
1. Run Configuration/Setup
2. System board
185 (Drive startup sequence information corrupted)
1. Run Configuration/Setup
2. System board
186 (Security hardware control logic failed)
1. Run Configuration/Setup
2. System board
187 (VPD serial number not set.)
1. Set serial number in Setup
2. System board
188 (Bad EEPROM CRC number 2)
1. Run Configuration/Setup
2. System board
189 (Three attempts were made to access the workstation with invalid passwords)
1. Run Configuration/Setup, enter the administrator password
2. System board.
190 (Invalid remote change requested)
1. Run Configuration/Setup
2. System board
191 (IBM embedded security hardware reset)
1. Run Configuration/Setup
2. System board
193 (IBM embedded security hardware removed)
1. Run Configuration/Setup
2. System board
195 (Asset ID antenna has been installed)
1. Run Configuration/Setup
2. System board
196 (System tampered cleared)
1. Run Configuration/Setup
2. System board
201 (Memory test error, see 'IBM Setup Utility main menu choices'). If the workstation does not have the latest level of BIOS installed, update the BIOS to the latest level and run the diagnostic program again.
1. Run memory diagnostics
2. DIMM
3. System board
229 (Cache error) Microprocessor 289 (DIMM has been disabled by user or system, see 'IBM Setup Utility main menu choices'.)
1. Run Configuration/Setup, if disabled by user
2. Disabled DIMM, if not disabled by user.
301 (Keyboard or keyboard controller error)
1. Keyboard
2. System board
303 (Keyboard controller error)
1. System board
2. Keyboard
602 (Invalid diskette boot record)
1. Diskette
2. Diskette drive
3. Cable
4. System board
604 (Diskette drive error)
1. Run Configuration/Setup and Diagnostics
2. Diskette drive
3. Drive cable
4. System board
662 (Diskette drive configuration error)
1. Run Configuration/Setup and Diagnostics
2. Diskette drive
3. Drive cable
4. System board
962 (Parallel port error)
1. Disconnect external cable on parallel port
2. Run Configuration/Setup
3. System board
11XX (System board serial port 1 or 2 error)
1. Disconnect external cable on serial port
2. Run Configuration/Setup
3. System board
1162 (Serial port configuration conflict)
1. Disconnect external cable on serial port
2. Run Configuration/Setup
3. System board
1200 (microprocessor machine check) Microprocessor 1762 (Configuration change has occurred) Run Configuration/Setup 1780 (Hard disk error)
1. Run Configuration/Setup
2. Hard disk drive
3. Hard disk drive cable
1781 (Hard disk error)
1. Run Configuration/Setup
2. Hard disk drive
3. Hard disk drive cable
1782 (Hard disk error)
1. Run Configuration/Setup
2. Hard disk drive
3. Hard disk drive cable
1783 (Hard disk error)
1. Run Configuration/Setup
2. Hard disk drive
3. Hard disk drive cable
1800 (No more hardware interrupt available for PCI adapter)
1. Run Configuration/Setup
2. Failing adapter
3. System board
1801 (Not enough space available to shadow ROM)
1. Run Configuration/Setup
2. Failing adapter
3. System board
1802 (Not enough I/O space available)
1. Run Configuration/Setup
2. Failing adapter
3. System board
1803 (Not enough memory space available)
1. Run Configuration/Setup
2. Failing adapter
3. System board
1804 (Not enough real memory space available)
1. Run Configuration/Setup
2. Failing adapter
3. System board
1805 (Adapter ROM checksum error)
1. Run Configuration/Setup
2. Failing adapter
3. System board
1962 (Drive does not contain a valid boot sector)
1. Verify a bootable operating system is installed
2. If RAID system, refer to the Hardware Maintenance Manual for the specific RAID adapter
3. Run diagnostics
4. Hard disk drive
5. Cable
6. SCSI Bbckplane
7. System board
2400 (Video controller test failure)
1. Video adapter (if installed)
2. System board
2462 (Video memory configuration error)
1. Video adapter (if installed)
2. System Board
5962 (IDE CD-ROM configuration error)
1. Run Configuration/Setup
2. CD-ROM drive
3. CD-ROM power cable
4. IDE cable
5. System board
6. Battery
8603 (Pointing device error)
1. Pointing device
2. System board
00012000 (Processor machine check)
1. Update BIOS
2. Replace microprocessor
00019501 (Microprocessor is not functioning - check VRM and processor LEDs)
1. Microprocessor
2. System board
00019701 (Microprocessor failed built in self test (BIST))
1. Microprocessor
2. System board
00180100 (No room for PCI option ROM)
1. Run Configuration/Setup
2. Failing adapter
3. System board
00180200 (No more I/O space available for PCI adapter)
1. Run Configuration/Setup
2. Failing adapter
3. System board
00180300 (No more memory above 1MB for PCI adapter)
1. Run Configuration/Setup
2. Failing adapter
3. System board
00180400 (No more memory below 1MB for PCI adapter)
1. Run Configuration/Setup
2. Failing adapter
3. System board
00180500 (PCI option ROM checksum error)
1. Remove Failing PCI Card
2. System Board
00180600 (PCI device failed built in self test (BIST))
1. Run Configuration/Setup
2. Failing adapter
3. System board
00180700 (xxxxyyyy planar PCI device not responding (where xxxx is PCI vendor ID and yyyy is PCI device ID)
1. System board
2. PCI card
00180800 (Unsupported PCI device installed)
1. System board
2. PCI card
00181000 (PCI error)
1. System board
2. PCI card
01295085 (ECC checking hardware test error)
1. System board
2. Microprocessor
01298001 (No update data for microprocessor)
1. Ensure all microprocessors are the same stepping level and cache size
2. Microprocessor
01298101 (Bad update data for microprocessor)
1. Ensure all microprocessors are the same stepping level and cache size
2. Microprocessor
01298200 (Microprocessor speed mismatch) Ensure all microprocessors are the same speed. I9990301 (Fixed boot sector error)
1. Hard disk drive
2. If RAID system, refer to the Hardware Maintenance Manual for the specific RAID adapter.
3. SCSI backplane
4. Cable
5. System board
I9990305 (Fixed boot sector error, no operating system installed) Install operating system to hard disk drive. I9990650 (AC power has been restored) (Virus warning) (Boot sector has changed)
1. Check cable
2. Check for interruption of power supply
3. Power cable
Other numbers
1. Run Configuration/Setup
2. Run virus detection software. Follow instructions on screen.
1 yorum:
I would like to thank you for the efforts you have made in writing this article. I am hoping the same best work from you in the future as well.
Yorum Gönder